Näytetään tekstit, joissa on tunniste Motors. Näytä kaikki tekstit
Näytetään tekstit, joissa on tunniste Motors. Näytä kaikki tekstit

perjantai 13. kesäkuuta 2014

Air cleaner and water intake prevention

Since it's been raining cats and dogs for a few days and preventing me from driving the bike to work I got anxious to do something about the waterproofing of the DC motor in the kWsaki. Here's what I've come up with.



The tower consists of Biltema part numbers 88463 (hidden inside), 32323 (air filter) and 88471. I have an 8" fan which I'm also planning to put inside the big adapter piece, so that the motor will always have more than enough airflow, even at low rpm. I just don't have the fan with me right now. Pictures of the installation later.

Update: If you're wondering what this has to do with waterproofing, my thinking is that adding the filter and moving it a little further away would mean less water in the motor. Water entering the filter at standstill should also not find it's way inside the motor nearly as much as it does now. This setup also gives me the option of moving the intake filter somewhere else using some flexible tube.

lauantai 22. maaliskuuta 2014

Motor mount vol. 3

I've bent two motor mounts so far. These electric motors sure have a lot of torque. They'll quite easily rip to pieces a less than perfect motor mount even just be going back and forth in your driveway in 3rd gear or reverse. Here's another take. It's not exactly very pretty, but I'll clean it up later if it stays in one piece.





perjantai 24. tammikuuta 2014

More explicit motor pics




As you can see, I managed to take both TTL200C motors apart. Identical shafts except that the other one is splined and the other one has a keyhole. I'll probably end up using the keyed one after all, but it all depends. I'm once again rethinking my coupling, but more on that when I have something to show.

Also took apart the other one a bit more to reveal a bit more rust. I'll need to get some of it off and put some paint on instead. Also turned the bolts that hold the brush holder to face outward so I can more easily swap whatever I decide to use as finger protection. Everything under the hood must pass the finger test, which means no live parts should be touchable with the UNECE R100 test finger.

maanantai 20. tammikuuta 2014

Interpretations

How to interprete me. If I say I'll leave something be for a while it means that I'll probably go do something about it right away. Example follows. Yesterday I wrote a post and honestly thought I'd leave the car be a while, but then inspiration stroke and I just had to go see if the rather unsettling noise the motor had made was because of my DIY coupling, transmission or the motor itself. Turns out it was, at least partially, due to the motor. I took the motor off and spun it, which resulted in more than usual twisting about and a rather nasty whiny noise. So I  pulled the motor from the car completely.



A point to take home from this is "Don't open the hood if it has 10cm of snow on it. It'll rain down on everything." Well, it's just snow. The equipment should be able to handle it. Otherwise it won't have a very long life in a car anyhow.

Since the motor was making a nasty noise and I had been thinking of swapping the insides of my two otherwise identical motors due to them having different shafts and only once casing having the required identification plate with vital information despite obviously being otherwise identical, I decided to give the TTL-200C motor disassembly a go. It turned out to be much easier than I had ever dreamed.





Hooray. Looks like I'll have some cleaning up to do. I'll also see if I can detach the other end of the motor which holds the brushes. The only reason would be to clean it up a little and perhaps give it a fresh coat of paint. The old paint is pretty much gone and rust has started taking it's place, which doesn't make it really pretty. Oh and I'll have to see if I can get those bearings off and replaced for good measure. Especially since the casing I will be using had that nasty noise, most probably caused by the bearing at the brush end. As you can see the motor has no fan built-in, so it probably needs some external help to move the extra heat away.

keskiviikko 10. heinäkuuta 2013

All kinds of progress

I've been making all kinds of progress. The motor is mounted to the car and I also decided on a controller. In fact, I went ahead and ordered the whole lot, including the controller, a DC/DC converter and an assembly for the controller.

But first things first. I pieced together something to firmly attach the four points that needed attaching. The motor itself, the transmission, the drive shaft and one of the original motor mounts. The only way to get it done was to just try to position everything the way they seemed want to be and start welding together pieces of steel to keep them there permanently.

I think it came out quite fine. You can judge for yourself be looking at the pictures below. The little triangular piece attaches the drive shaft and the motor from below.







I was browsing the Kelly Controls website when I came across their KHD12600D controller, which they had on sale. I added the assembly for it and a DC/DC converter too. They had reasonable prices and also reasonable shipping fees, which is not usually the case. They came through amazingly as well. I put in the order on Sunday, got an email from Kelly on Monday and DHL delivered the package today, Wednesday. Ten out of ten for both Kelly and DHL.



As you can see the controller came fully assembled with contactor, pre-charge resistor, diode and fuse. Very nice. The only ugly part was the crap on the other end of the DC/DC converter. Not very professional. Tried to clean it up a bit myself to make it a little more bearable. That was after I had taken the photo.

Next up mounting the assembly into the car and loaning the battery pack from the kWsaki electric motorcycle. Obviously a box to put the batteries in must also be deviced. After that it should be time for a little test drive. If that goes well I'll need to tackle the nasty but important power brakes and cabin heating.

torstai 23. toukokuuta 2013

Spin of the Wheel


So I had a test fitting of the motor. Everything else went pretty nice, except my attempt in finishing the adapter plate contruction in place turned out to be a little challenging. In the end I also decided that I'll drop the flywheel and the clutch altogether and go for a direct coupling. It'll save weight and I noticed that the electronically driven tachometer didn't want to work anyway without the ICE in place. So after I had got the wheels spinning I took everything apart again.

As you can see it really is better to be lucky than to be good. One of the bolt holes in the drive shaft support just fits a hole in the motor. I'm not sure it's quite enough to hold the support in place and if it will still match after I've taken the flywheel and clutch out, which may alter the motor position.

torstai 18. lokakuuta 2012

Brush and motor gallery

Now I realize this will be for a very limited audience, if anyone, but here's a a bit of brush gallery of my TTL-200C motors. The measurements are obviously metric.





What the heck. Here's a couple more shots of the motors themselves.



They're about 8 inches in diameter and they don't have an internal fan so an electric blower must be added. Perhaps the converted turbocharger thing Jack sells on EVTV store or something like it. As you can see in the background of some of the pictures the motors came with shrouds which had a hole for a blower, but the shrouds were at the wrong end of the motor (not the commutator end as they should be) so they will need a bit of modification to fit the correct end. That's because the commutator end is partially blocked by the plastic box which covers the wiring.

By the way there are four poles in that plastic box with two of them connect by a copper bar. That's all well and understandable for a series motor, but when I got the motors the other one had three wires coming out. One in A1, one on the copper bar connecting A2 and D1 and the third on D2 (I'm trying to remember the markings right). I wonder what the mystery third wire is for if they really are series wound. It does say SERIES MOTOR on the nameplate. I heard that the motors they ended up using in the Elcat EVs were actually compound motors which would have three wires, but why are they here? Could you use the third wire for some sort of regen without hurting the brushes? Let me know if you have an idea. I'll have to take some measurements to make sure these aren't really compound or SepEx motors too, but I doubt it very much at this point. Most likely the third wire is a mistake of some sort.


sunnuntai 14. lokakuuta 2012

Get your motor running

Got my motor running, actually. A couple of times even. First with a lazy 12 volt battery and then connected to my motorcycle. Here's a video of the latter.


I was going to remove the batteries and whatnot from the motorcycle first and then bolt everything nicely to a test bench like I did with the motorcycle parts when I first got them, but then I got lazy and decided to just take the motor to the bike.

Next up: jacking up the car and removing liquids. Looking forward to it! Not really. I'll hate it.

lauantai 6. lokakuuta 2012

Got motors!

Just picked the two old Elcat motors from Järvenpää and here they are in the trunk of my diesel car:


The motors are a bit different. The other one has a long shaft with keyhole and the other one a short shaft with teeth. Both have a Subaru motor plate on them and some sort of an adapter which can hopefully be modified to fit the Citroën flywheel. Good times.


Edit: Apparently these motors were not used in any production Elcats. They were just prototypes. I wonder why they weren't chosen? Let me know if you have more information. Continous 60 minutes kW rating seems a little less than in production specs, but on the other hand max rpm is higher at 8000.

perjantai 5. lokakuuta 2012

Elcat motor(s)

I'm going to go look at two old motors from the venerable Finnish electric car Elcat. They're old and the put out only about 22 kW and 73 Nm, but they are quite affordable as well. Plus there's two of them for sale so I can keep the second one as spare parts or put one in now and work on the other to make it all shiny and new again. The motors are Thrige model TTL-200C.


The motors used to power these little vans which originally had a 72 volt system based on lead acid cells. What this means is that I could actually keep to 72 (or 75) volts nominal as with the motorcycle and keep using the chargers and controllers that I've used to. Testing with 96-99 volts nominal would be interesting, but would also require investing in a much more expensive controller. I'm also not sure if raising the voltage would give me any more useful power out of these old motors. Their useful powerband ends after 2000 rpm as you can see from the graph below.


Another aspect of these motors is their size. They're said to be 50-60 cm long which may or may not be a problem. Luckily my car of choice is not too small and the original engine is not very small either. Looking at the pictures I've taken I think I'll be alright. There's one measurement I should have taken that I didn't, but as I'm about 250 km away from the car at the moment I'll just have to wing it.

Component selection

I'm also searching for suitable components for the car. I got a lucrative offer for an AC system from Amotec Oy for around 5000€ including an AC-50 motor, controller and everything else including liquid cooling. On the pro side of things are the obvious benefits of AC propulsion, such as being maintenance free and having regenerative braking, but on the cons is the somewhat steep price to be paid right away.

ICE to be removed

On the DC side of things I could just get the motor first and test everything which the 72 volt system from my motorcycle including batteries, controllers and so on. For the motors there are multiple candidates such as Netgain Warp 9, Kostov 10" and Motenergy ME1002. I used a much smaller ME1003 (get a clue with the naming, please!) in my motorcycle and the ME1002 specs look nice. Price is also tempting. The problem is finding a dealer for these motors without paying through the nose for the shipping. The best offer so far is little less than 2k€ for the Kostov from Rebbl with taxes and shipping. I'm waiting for a quote from PalonenLABS for the same motor.

As for the batteries the new CALB CA-series is the obvious choice. However, considering that I already have 25 of the older SE-series type SE40AHA I might be tempted to recycle them. Add another 8 and I have my first set of 33 for 99 volts nominal or about 110 volts fully charged. Add another 66 and I have 99 for the same voltage, but 120 Ah or about 12-13 kWh of stored energy. That, incidentally, is the size of the battery pack in the i-MiEV, if my memory serves me right. The batteries would then be connected in 3 parallel and 33 series or 3p33s (perhaps 33s3p). There would also be some inherent flexibility in battery placement. I could for example put one series of 33 under the hood and the remaining 66 in the back for a weight distribution of 33% in the front (50kg) and 66% in the back (100kg). I could also purchase one set of 33 at a time. I would however lose the improvements in the CA-series, most notably better performance in cold temperatures. I will heat the battery boxes anyway, so it might not be a problem though.

perjantai 17. elokuuta 2012

Springs and problems

It's a day of good news and bad news. The bad news is that the motor I got does not appear to be in perfect condition. The commutator seems to be out of round as you can see the brushes moving in the following video. Not really quite sure how this has come to be. I haven't had a reply from the seller yet. The motor also gets very hot.

Update: I have gotten into touch both with the seller and Motenergy. They don't see a problem in the video so I suppose everything is in order after all. Motor heating might also be within limits. Maybe.


The good news is that my new progressive front springs from Hagon arrived early! I wasn't really expecting them in weeks since they are made to order for this somewhat rare bike. I knew there was a package coming, but I assumed it would be the LED lights for the bike I ordered from dealextreme.com.


Good looking springs with proper installation instructions included. Hopefully they will also solve my problems with the front fork and it will finally become as nice to ride as it should be.


perjantai 13. heinäkuuta 2012

Motor mounted

I got the mounting plate from Hydroala today and immediately proceeded to mount the motor. I had already secured the battery to the chassis earlier. The motor mount will still need some additional support to prevent unwanted sideways movement. I also changed the rear sprocket to a new 49 tooth and tried to fit the 112 link chain I had acquired. Unfortunately I will need four more links for it to be long enough. Hopefully I can swap it for a longer one tomorrow or at least put one on order. The front sprocket I have also has a hole of correct bore in it now, but still no keyhole. We'll see if I can have one made or do I have to just give up and order a finished sprocket online. I may go for a 12 tooth if it comes down to that. One tooth less than what I have now. Funnily enough one tooth equals 10km/h more top speed with 13 teeth at about 130km/h. Next up along with solving the sprocket issue is mounting the rest of the equipment. A moderate amount of work I hope.





keskiviikko 4. heinäkuuta 2012

It's fracking huge!

It has been unboxed. Now I knew the dimensions and the weight. But it's still fracking huge in real life! That goes especially for the controller the dimensions of which I didn't really pay attention to in advance. It'll be an interesting challenge to fit them all in. Here's the family portrait for you. Enjoy!