maanantai 25. maaliskuuta 2013

What's wrong with Top Balancing

Let's go over the basics again. Top Balancing is based on a belief that you can fully charge a cell by charging it to a certain voltage, say 3.65 volts, and just keep it there. To get a complete pack "balanced" would require to charge until all cells are at 3.65 volts. To do this some cells need to be kept at 3.65 volts while others catch up. That's all part of Top Balancing and what many BMS do.

So how did they come up with this system that many people swear by and even think to be absolutely necessary? They probably don't know themselves, but here's how I think it must have happened. We know that a LiFePO4 cell likes to stay within a certain voltage range. Go below 2.5 V and you start hurting the cell. Go above 4 V and you're definitely hurting it. To charge a battery you put current into it and since you know you don't want to go over a certain voltage you stop when it's reached. This was 4.2 V in the beginning, but I guess they've found it a little too high since 3.65 V is what most recommend now. They also found out that if you taper the current you can put a little more energy into the cell while keeping the voltage at 3.65 V.

Now think of Lead Acid for a moment. In Lead Acid voltage is voltage and voltage is charge level. You charge and you keep trickle charging your Lead Acid batteries, they'll be happy for it and you get a nicely Top Balanced Lead Acid pack. The more energy you can put into them the happier they are and the more range you will get from you Lead Sled.

Now if you put these two things together, maximum charge voltage and Lead Acid heritage, what you get is Top Balancing and what usually is considered to be a Lithium BMS. To prove this they talk about stuff like Cell Drift and Self Discharge. I really don't know how they came up with them, but it must be from Lead Acid heritage as well. Or maybe they put this Top Balancing BMS on their cells, kept recording the voltages and noticed that they vary and the cells will Self Discharge.

What they didn't think of was that they had the BMS connected the whole time and both phenomena were actually caused by the BMS itself. If you put any Cell Level system on your cells that's not very, very carefully designed not to draw any (and I do mean any) current, you will see the cells react and they will react differently. You will place on uneven load on the cells that will cause "Cell Drift" and the load itself will be the "Self Discharge" you see. To make matters worse, if you Top Balance and keep cells at 3.65 V while other catch up, you will damage your cells and damage them by different amounts, which will only inflate the problems you think are caused by the cells themselves.

But what about internal resistance, you ask. What about it? What part of Top Balancing BMS will have any effect on the internal resistance of the cell? Yes, the cells may have varying internal resistance and that variation will cause them to discharge at a different rate. Let's say you have a pack of cells and you'd charge them each individually to 3.65 volts without damaging them by "boiling" some at that voltage while others catch up. You'd end up with fully charged cells, right? Now what happens when you start discharging them as hard as you can? You know they have different internal resistance and slight variation in capacity, because they just can't make them perfect yet.

So you're discharging and discharging and your first cells hit the cut-off voltage. You have to stop now, or you'll damage those cells. And you'll better be quick about it too. Stop the car immediately. If you were smart you had already put the vehicle into a Crawl Mode, so that you could pull over safely. Unless you've kept a really good track of previous full discharges you won't know when your first cells will be empty and when you should start crawling. Doing so gets really complicated and expensive really fast. Add in all the single cell level monitoring, shunts to enable Top Balancing and it's not really hard to imagine why those BMS systems are so expensive.

Hopefully I've by now convinced you of the problems with and caused by Top Balancing. I'd really like the whole world to get a clue on this, including Boeing and the BMS people at Sähköautot - Nyt! forum, but I don't have my hopes up. What's amazing is how firmly rooted these false beliefs are. It may just be that a lot of people have too much invested in BMS systems to admit there are issues. It sure does seem like a lot of people are looking to make a buck on these.

I guess I still have the obvious question unanswered. If Top Balancing doesn't do what people think it does and if it doesn't really solve anything, what is the answer? How about if we try something quite opposite. Instead of trying to Top Balance the cells we drain them as empty as we dare. 2.5 volts is a little dangerous so let's say 2.75 volts. Let's call that empty, or close enough.

Now if we have all of our cells empty and we connect them in series with just the interconnects we have an empty pack. What happens if we charge them? They will all receive the same amount of current. They're all a little bit different so they absorb their share a little differently, but it doesn't matter. We don't like any cells to go above into dangerous territory so we undercharge a little. We don't even pretend to get all cells at exactly 3.65 volts. Most end up a little below and some may even go a little higher, but it doesn't matter. We accomplish this by charging the whole series pack to cell count times 3.5 volts. My experience is that even with this undercharge you will end up putting as much or even more energy into the cells than what they are rated for.

What you've in essence accomplished by this Bottom Balancing is that you've zeroed all the differences between the cells, whether it be capacity or internal resistance. When you discharge the cells they will do the same thing in reverse that they did when you charged them and if you keep discharging them they will all end up at the same voltage you Bottom Balanced them at. In other words they will both charge and discharge very close the same way. Close enough that it doesn't matter. As a bonus you don't have to keep track of your cells. You'll now exactly how many Ah went into the pack when you charged it and you know exactly how much you can take out. And once those cells hit that 2.5 volts, all together, at the same time, they will be putting out hardly any energy at all. And since they're all empty they can't force each other into destruction.

Disclaimer: All of my battery ramblings are based on my own experience and Jack Rickard's findings. They are applicable to CALB SE- and CA-series cells. Other cells and chemistries may at least require different voltages.

3 kommenttia:

  1. I'm definitely going to try the bottom balancing route myself, when I finally begin my own conversion in June/July. I'll be monitoring the cells myself regularly and when I do, I'll definitely report all my data.

    VastaaPoista
    Vastaukset
    1. Sounds good to me! The funny thing about BMS people is that when you present this to them and they start coming up with counter arguments they never have any data to back up their claims. So far I haven't seen a single data set showing cell drift or self discharge that didn't have a BMS connected to the pack. It's all just universally taken as granted. Oh, they do refer to some super secret research material they claim to have seen, but of course they can't tell you about it.

      Poista
    2. I've been following this particular discussion close by at Sähköautot-forum, intrigued. I've been playing with RC batteries long enough to trust my own eyes and I'm confident I can do the actual monitoring myself with more certainty than just leave the pack to be managed by some BMS. Or worse, miniBMS that just does the top balancing with very little monitoring. I really look forward to trying out the bottom balancing. The whole method is really beautiful in it's simplicity.

      Poista